Stage 4 Reference Quality Class D Mono Amplifier with 2,400 Max Power

  • 1200 Watts of Continuous Power
  • SIgnal-to-Noise Ratio: 70db
  • Multi-Amplifier Synchronization System (MASS)


The Heart of a Champion
Every year, Pioneer gathers its top installers to compete in its revered Sound Build-off. In 2010, the PRS-D1200SPL was selected as the mono-channel amplifier of choice for the competition. See what these Stage 4 retailers have to say about the PRS-D1200SPL and its amazing low-end performance.

The "Stage 4" PRS-D1200SPL amplifier features huge power delivered with low heat and distortion, thanks to its Class D technology. It provides Bass Boost, a subsonic filter, and a variable crossover, and it's 1-ohm mono stable. Plus, you can externally bridge 2 amps together, increasing power and still keeping things simple to operate.

Externally Bridgeable
The units are externally bridgeable and permit two separate amplifiers to be joined together as one, doubling the power to a single woofer or voice coil. That's over 2400 Watts RMS (4800 peak!) with the PRS-D1200SPL, ideal for use in serious SPL competition vehicles. Best of all, no special cable is required - a simple RCA cable and proper setting of the Sync mode will get this.

Multi-Amplifier Synchronization System (MASS)
Pioneer's proprietary Multi-Amplifier Synchronization System (MASS) technology allows one amplifier (the master) to control the settings of other amplifiers when two or more amps are “strapped” together. Especially important for multi-amplified systems, this powerful Pioneer technology eliminates the need to adjust each amplifier gain separately.

Huge 4 Gauge Power/Ground Terminals
Big amplifiers need big power, and the PRS-D1200SPL is designed to ensure it can always perform its best. The huge terminals support wire up to 4 gauge.

Dynamic Amplifier Protection (DAP)
A specialized protection circuitry called Dynamic Amplifier Protection (DAP) has also been applied. DAP, quite simply, protects the amplifiers from failing. The amps automatically reconfigure themselves based on output signal level. Designed with the highest possible power carrying capability — also known as “low current density” — DAP ensures the utmost in unit reliability and efficiency.

Subsonic Filter
The subsonic filter lets you remove power-robbing frequencies below the tuning of your subwoofer/enclosure. The subsonic is set at 20Hz with a steep 24dB/Octave rolloff for optimal effect.

Variable Crossover (40~240Hz)
For added flexibility, the variable crossover lets you set the levels at which higher-frequency signals will be filtered out, so that the remaining lower-frequency signals get sent to your sub(s). Where they belong. This optimizes your system’s efficiency and delivers the best possible sound quality. You can adjust it continuously between 40 to 240Hz, as well as selecting from either -18dB/Octave or -24dB/Octave rolloff, giving you the ultimate flexibility in setting up your system.

Variable Bass Boost
Bass boost gives you more control over how your music sounds. You can adjust the tuning frequency from 40 to 120Hz, as well as the level from 0 (flat) all the way to 12dB of boost.

  • Mono
  • 2,400 W
  • 1,200 W x 1
  • 1,000 W x 1
  • 500 W x 1
  • 10 Hz to 240 kHz
  • < 0.3% (1 kHz)
  • > 80 dB
  • 15" x 11-1/8" x 2-5/8"
Main Features
  • Class D
  • 1 to 8
  • 2-Ch. (Gold-Plated)
  • 401 mV to 6.5 V
  • Block-Type
  • LPF
  • 40 Hz to 240 Hz
  • -24 dB/oct.
  • 40 Hz to 120 Hz
  • 0/6/9/12 dB

Other Important Resources